Skidsteer Stump Grinder with swing cylinder- S24
The S24 skid steer stump grinder features a specially designed 12V diverter valve to allow control of the hydraulic swing cylinder, for a more refined cutting pass. Combined with our flow control this remote will give you precise control of the cutting pass and allow you to grind more of the stump without repositioning. Cutting depth is up to 15" below ground with a swing radius of 80 degrees. The floating deflector safely directs the flow of debris for quick clean up. The S24 is a good choice for skidsteer stump grinding on close cut grass such as golf courses as well as for stump grinder rental on medium sized skidsteers and track loaders. The massive ¾" thick steel rotor provides the back bone for the Stump Grinder cutting system. The carbide tipped teeth are incredibly hard material ensures reliable cutting performance. The high number of teeth means that each tooth needs to do less work. Each of the Stump Grinders teeth only need to make a small cut, because the work is shared by more of our rugged teeth they last longer and usually only require 2 or 3 replacements at a time.
The bolt-on designed teeth allow for straightforward replacement. The Stump Grinder’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. More chip clearing produces smoother operation and reduces heat build-up that can damage the rotor and cause premature tooth failure. Fine tune the performance of your Stump Grinder easily with the Flow Control knob. The Flow Control allows you to adjust the cutting pass speed, to match the size and performance of your tractor. A S24 with a motor of S445 having a PSI of 2500 can cut a stump of 24 inches in 60 mins at 15 GPM, whereas the same motor parameter and increased PSI of 3000 can cut a stump of 24 inches in 50 mins at 15 GPM and with a PSI of 3500, the time taken will be 50 mins at 15 GPM. If the GPM is increased to 20, the time taken will be reduced.
For best stump grinding performance we offer multiple motor options to exactly match the hydraulic flow of your skidsteer as well as 8 pin and 14 pin AUX electrical plugs as well as the 7 pin Bobcat so you can use the controls in your cab with no extra wiring or hand controls.
SOLD BY EQUIPMENT DEALERS
All Baumalight products are sold through our network of equipment dealers. For you, this means better product support, after-sales service, maintenance and product warranty from your local, trusted dealership Click here to find a local dealer.
D004460 OPTIONAL HAND CONTROL
Is one of your skidsteers older, without an auxiliary electrical connection? We also have an in-cab adapter to plug into your Aux Electrical Connected attachments that will allow you to run them. Plug the adapter into the attachment, connect it to 12V and now you can run your new attachment on an older skidsteer.
AUX Plug
Baumalight now offers a more direct and simple way of connecting to your skidsteer’s auxiliary electrical connection. Simply connect the hydraulics and plug in the electrical. Now you can control the attachment from inside your cab.
Carbide Tipped
Like the finest saw blades, the cutting teeth on Stump Blasters are carbide tipped. This incredibly hard material ensures reliable cutting performance. When grinding stumps, buried hazards are inevitable; gravel, stones even metal posts are not uncommon to “find”. Our carbide teeth are designed to stand up to this abuse and keep on blasting stumps to dust.
6 FREE TEETH
All S24 Stump Grinder comes with a free set of 6 replacement teeth. These replacement teeth are conveniently shipped in a robust enclosed compartment on top of the frame.
More Teeth
The high number of teeth means that each tooth needs to do less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of our rugged teeth they last longer and usually only require 2 or 3 replacements at a time. The bolt-on designed teeth allow for straightforward replacement.
Rotor
The massive ¾" thick steel rotor provides the back bone for the Stump Blaster cutting system. It’s the anchor for the carbide tipped teeth. For smooth operation it’s important that the rotor remains solid, with no flexing. The rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps.
Flow Control
Fine tune the performance of your Stump Blaster easily with the Flow Control knob. The Flow Control allows you to adjust the cutting pass speed, to match the size and performance of your tractor. This gives you the smoothest cut possible and with the full return back to the start position, the quickest overall stump grinding time possible.
Hydraulic Motor
Skid steer mounted Stump Blasters run on hydraulic motors. For best results, match your equipments flow rate to one of our available hydraulic motor options.
More Clearance
The Stump Blaster’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. More chip clearing produces smoother operation and reduces heat build-up that can damage the rotor and cause premature tooth failure.
Floating Deflector
The deflector floats as you grind providing chip and debris control from first cut to maximum depth without getting in the way. In tight grinding situations the deflector can be flipped up out of the way.
HARDENED STEEL BUSHING
Spring Bushings made from high grade chrome-vanadium AISI 6150 spring steel on all main pivot points.
Greaseable Pins
Our grease pins are zinc plated to prevent corrosion which will allow for smoother operation of the units joints over their lifetime.
SOLD BY EQUIPMENT DEALERS
All Baumalight products are sold through our network of equipment dealers. For you, this means better product support, after-sales service, maintenance and product warranty from your local, trusted dealership Click here to find a local dealer.
D004460 OPTIONAL HAND CONTROL
Is one of your skidsteers older, without an auxiliary electrical connection? We also have an in-cab adapter to plug into your Aux Electrical Connected attachments that will allow you to run them. Plug the adapter into the attachment, connect it to 12V and now you can run your new attachment on an older skidsteer.
AUX Plug
Baumalight now offers a more direct and simple way of connecting to your skidsteer’s auxiliary electrical connection. Simply connect the hydraulics and plug in the electrical. Now you can control the attachment from inside your cab.
Carbide Tipped
Like the finest saw blades, the cutting teeth on Stump Blasters are carbide tipped. This incredibly hard material ensures reliable cutting performance. When grinding stumps, buried hazards are inevitable; gravel, stones even metal posts are not uncommon to “find”. Our carbide teeth are designed to stand up to this abuse and keep on blasting stumps to dust.
6 FREE TEETH
All S24 Stump Grinder comes with a free set of 6 replacement teeth. These replacement teeth are conveniently shipped in a robust enclosed compartment on top of the frame.
More Teeth
The high number of teeth means that each tooth needs to do less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of our rugged teeth they last longer and usually only require 2 or 3 replacements at a time. The bolt-on designed teeth allow for straightforward replacement.
Rotor
The massive ¾" thick steel rotor provides the back bone for the Stump Blaster cutting system. It’s the anchor for the carbide tipped teeth. For smooth operation it’s important that the rotor remains solid, with no flexing. The rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps.
Flow Control
Fine tune the performance of your Stump Blaster easily with the Flow Control knob. The Flow Control allows you to adjust the cutting pass speed, to match the size and performance of your tractor. This gives you the smoothest cut possible and with the full return back to the start position, the quickest overall stump grinding time possible.
Hydraulic Motor
Skid steer mounted Stump Blasters run on hydraulic motors. For best results, match your equipments flow rate to one of our available hydraulic motor options.
More Clearance
The Stump Blaster’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. More chip clearing produces smoother operation and reduces heat build-up that can damage the rotor and cause premature tooth failure.
Floating Deflector
The deflector floats as you grind providing chip and debris control from first cut to maximum depth without getting in the way. In tight grinding situations the deflector can be flipped up out of the way.
HARDENED STEEL BUSHING
Spring Bushings made from high grade chrome-vanadium AISI 6150 spring steel on all main pivot points.
Greaseable Pins
Our grease pins are zinc plated to prevent corrosion which will allow for smoother operation of the units joints over their lifetime.
There are currently no customer photos or video submitted for this Baumalight product.Please check out similar products to see if there are submitted media available for those . Visit our Factory Discount web page to learn how you could participate in our Media Discount Program with your Baumalight product.
| Model No. | S14 | S18 | S24 | S28 | S40 |
|---|---|---|---|---|---|
| Recommended HP Size | 12-30 | 25-80 | 30-80 | 50-120 | 50-120 |
| Maximum Carrier Size | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI |
| Motor Type | Gerotor | Gerotor | Gerotor | Gerotor | Bent Axis Piston |
| Hydraulic GPM | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart |
| Rotor Size | 18" | 24" | 24" | 24" | 24" |
| Number of Teeth | 12 | 34 | 34 | 34 | 20 |
| Tooth Construction | High speed | Planer | Planer | Planer | High speed |
| Cutting Wheel Speed | Depends on GPM | Depends on GPM | Depends on GPM | Depends on GPM | Depends on GPM |
| Cutting Height - Above Ground | No limit | No limit | No limit | No limit | No limit |
| Cutting Depth - Below Ground | 6" | 10" | 10" | 10" | 24" |
| Maximum Cutting Depth - Per Pass | 2" | 5" | 6" | 6" | 1" |
| Maximum Horizontal Cut | 12" | 22" | 22" | 22" | 22" |
| Swing Arc | Self-feeding | Self-feeding | 80° | 80° | 85° |
| Hub Torque | 150 Ft.-Lbs. | 250 Ft.-Lbs. | 250 Ft.-Lbs. | 803 Ft.-Lbs. | - |
| Over Torque Protection | Relieve valve | Relieve valve | Relieve valve | Relieve valve | Remote |
| Hitch | 1" pivot pins | 1" pivot pins | Quick Attach | Quick Attach | Quick Attach |
| No. of Remotes Required - Hydraulic | 1 | 1 | 1 | 1 | 1 |
| Requires 12 Volt DC | No | No | Yes | Yes | Yes |
| Unit Weight (Shipping) Lbs. | 394 | 642 | 995 | 995 | 1,200 |
| Model No. | S14 | S18 | S24 | S28 | S40 |
|---|---|---|---|---|---|
| Recommended HP Size | 12-30 | 25-80 | 30-80 | 50-120 | 50-120 |
| Maximum Carrier Size | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI |
| Motor Type | Gerotor | Gerotor | Gerotor | Gerotor | Bent Axis Piston |
| Hydraulic GPM | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart |
| Rotor Size | 18" | 24" | 24" | 24" | 24" |
| Number of Teeth | 12 | 34 | 34 | 34 | 20 |
| Tooth Part number | H3000 | S1000 | S1000 | S1000 | H3000 |
| Tooth Construction | High speed | Planer | Planer | Planer | High speed |
| Cutting Wheel Speed | Depends on GPM | Depends on GPM | Depends on GPM | Depends on GPM | Depends on GPM |
| Cutting Height - Above Ground | No limit | No limit | No limit | No limit | No limit |
| Cutting Depth - Below Ground | 6" | 10" | 10" | 10" | 24" |
| Maximum Cutting Depth - Per Pass | 2" | 5" | 6" | 6" | 1" |
| Maximum Horizontal Cut | 12" | 22" | 22" | 22" | 22" |
| Swing Arc | Self-feeding | Self-feeding | 80° | 80° | 85° |
| Hub Torque | 150 Ft.-Lbs. | 250 Ft.-Lbs. | 250 Ft.-Lbs. | 803 Ft.-Lbs. | - |
| Over Torque Protection | Relieve valve | Relieve valve | Relieve valve | Relieve valve | Remote |
| Hitch | 1" pivot pins | 1" pivot pins | Quick Attach | Quick Attach | Quick Attach |
| No. of Remotes Required - Hydraulic | 1 | 1 | 1 | 1 | 1 |
| Requires 12 Volt DC | No | No | Yes | Yes | Yes |
| Unit Weight (Shipping) Lbs. | 394 | 642 | 995 | 995 | 1,200 |
CANADA
UNITED STATES
INTERNATIONAL 
SKIDSTEER STUMP CUTTING TIMES BASED ON 24" STUMP
|
* Motor will run at this PSI, but excess pressure is dumping over relief.
5 GPM is used for swing cylinder.
HOW TO CHOOSE THE RIGHT MOTOR
The most important part of choosing the right BrushFire is matching the correct motor option to your equipment. It can make a huge difference. In this video, we explain how to use our charts to determine which motor is right for you!
Updated as of March 22, 2023 2:39 PM EDT
UPCOMING PUBLIC HOLIDAYS
| Date | Description |
|---|
STUMP GRINDERS
| Model Number | Discount Available | Lead time to build first order | Lead time to build next order | Location | Notes | Discount Description |
|---|---|---|---|---|---|---|
| WB44 | 10% | MTB | New unit in a crate that has sat round for a while | |||
| HGW30 | 10% | MTB | Refurbished HGW30 BL1009517 with full warranty | |||
| 1P24 | MTB | Discount on multiples of two | ||||
| D005735 | Extension bracket kit for 1P24 | |||||
| S1050 | S1050 valve kit (shipped w/o stump grinder) | |||||
| 3P24 | ||||||
| 3P24-S1050 | S1050 kit mounted. | |||||
| 3P34 | ||||||
| 3P34-S1050 | 7% | 1 in stock in green, color is free and discount on the unit (BL1011875) S1050 kit mounted. | ||||
| 3P40 | ||||||
| 3P40-S1050 | S1050 kit mounted. | |||||
| S14 | ||||||
| S14-S250 | MTB | Stock w/S250 and D001126 mini plate | ||||
| S16 | 60% + more for media | Pre-Production Discount | ||||
| S18-S450 | MTB | Stock w/D001127 plate | ||||
| S18-S550 | MTB | Stock w/D001127 plate | ||||
| S18-S650 | MTB | |||||
| S24-S445 | ||||||
| S24-S545 | ||||||
| S28-S645 | ||||||
| S40 | ||||||
| HGS50F | ||||||
| GXM350 | ||||||
| GXM350-X508 | ||||||
| GXM350-X510 | ||||||
| GXM550 | ||||||
| GXM550-X510 | ||||||
| GXM550-X530 | ||||||
| GXM750 |
PUBLIC HOLIDAYS
| Date | Description |
|---|---|
| 2023-04-07 | Good Friday |
| 2023-05-22 | Victoria Day |
