Stump Buster

3 Point Hitch Stump Grinder - 3P34

The 3P34 PTO stump grinder is designed for tractors equipped with a 50–80 horse power motor allowing you to grind into stumps with a 34" Rotor carrying 54 replaceable carbide teeth. The Stump Blaster’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. The rugged gear box takes up to 80 HP and develops 803 ft/lbs of stump destroying torque. A stump of 30" width and 12" depth can be ground in 4 mins with a 80HP tractor, with 70HP it takes around 5 mins and 60 HP takes 6 mins to finish the work. The massive ¾" thick steel rotor provides the back bone for the Stump Blaster cutting system. It’s the anchor for the carbide tipped teeth. For smooth operation it’s important that the rotor remains solid, with no flexing.

The rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps. Designed for Cat 2 3PH and 540 PTO this versatile stump grinder has a cutting depth of 25" above ground and 14" below ground. With direct drive from the engine, all the way through the heavy duty gear box to the teeth, a stump grinder on the PTO of a tractor is the most efficient way to use a stump grinder for lawn care or fence row clearing. Spring bushings made of high grade chrome-vanadium AISI 6150 spring steel are provided on all main pivot points. The swing cylinder gives the operator a 65 degree grinding range without moving the tractor. The heavy duty base provides a solid base for grinding. This allows for more consistent grinding performance and reduces the stress on your tractor.

SOLD BY EQUIPMENT DEALERS

All Baumalight products are sold through our network of equipment dealers. For you, this means better product support, after-sales service, maintenance and product warranty from your local, trusted dealership Click here to find a local dealer.

Local Support

SERVICE AND INSTRUCTIONAL VIDEOS & RIGHT TO REPAIR

Baumalight offers customers a series of helpful service & instructional videos and supports the right to repair. These videos show you how to perform your own trouble shooting and repairs which can save you a lot of down time because many things can be fixed on the spot by end users. Also, after the warranty period is over, a lot of money can be saved if you can do things yourself following simple instructions on trouble shooting, maintenance and repairs.

CLICK THE VIDEO TO LEARN MORE

Service And Instructional Videos

S1050 External Control (Optional)

This optional control is mounted on an adjustable arm. The control is great for smaller tractors with limited HP for better cutting control and for tractors with only one remote.

Note: Cost to add in the field is greater than if order with unit from factory as there is extra freight and a completely new hose set will be required so you will see a better price if it is ordered to be mounted at the factory.
Part number is S1050 to order this for field installation.

Flow Control

Fine tune the performance of your Stump Blaster easily with the Flow Control knob. The Flow Control allows you to adjust the cutting pass speed, to match the size and performance of your tractor. This gives you the smoothest cut possible and with the full return back to the start position, the quickest overall stump grinding time possible.

Flow Control

Carbide Tipped

Like the finest saw blades, the cutting teeth on Stump Blasters are carbide tipped. This incredibly hard material ensures reliable cutting performance. When grinding stumps, buried hazards are inevitable; gravel, stones even metal posts are not uncommon to “find”. Our carbide teeth are designed to stand up to this abuse and keep on blasting stumps to dust.

Carbide Tipped

6 FREE TEETH

All 3P34 Stump Grinder comes with a free set of 6 replacement teeth. These replacement teeth are conveniently shipped in a robust enclosed compartment on top of the frame.

6 free teeth

More Teeth

The high number of teeth means that each tooth needs to do less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of our rugged teeth they last longer and usually only require 2 or 3 replacements at a time. The bolt-on designed teeth allow for straightforward replacement.

Multiple Teeth

Gearbox

The rugged gear box transfers power from the tractor’s PTO to the rotor creating 803 Ft.-Lbs of torque and turning the rotor and hungry teeth at 810 RPM.

Gearbox

Rotor

The massive ¾" thick steel rotor provides the back bone for the Stump Blaster cutting system. It’s the anchor for the carbide tipped teeth. For smooth operation it’s important that the rotor remains solid, with no flexing. The rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps.

Rotor

More Clearance

The Stump Blaster’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. More chip clearing produces smoother operation and reduces heat build-up that can damage the rotor and cause premature tooth failure.

More Clearance

Stabilizer Base

The heavy duty base provides a solid base for grinding. This allows for more consistent grinding performance and reduces the stress on your tractor.

Stabilizer Base

Floating Deflector

The deflector floats as you grind providing chip and debris control from first cut to maximum depth without getting in the way. In tight grinding situations the deflector can be flipped up out of the way.

Floating Deflector

HARDENED STEEL BUSHING

Spring Bushings made from high grade chrome-vanadium AISI 6150 spring steel on all main pivot points.

Hardened Steel Bushing

Greaseable Pins

Our grease pins are zinc plated to prevent corrosion which will allow for smoother operation of the units joints over their lifetime.

Greaseable Pins

Swing & Lift Cylinders

Get right to grinding with less maneuvering of your tractor and less damage to the grass. The swing cylinder gives the operator a 65 degree grinding range without moving the tractor. The lift cylinder allows you to raise and lower the grinding head to get in start position as well as lowering the head after a pass so you’re ready for the next bite.

Swing and lift cylinders

Down below are photos and video footage taken by Baumalight product owners. Visit our Factory Discount web page to learn how you too can participate in this media discount program.


CUSTOMER PHOTOS

CUSTOMER VIDEO



Model No. 1P24 3P24 3P34 3P40
Recommended HP Size 20-45 25-55 45-80 60-120
Maximum Engine HP 50 58 85 125
Maximum PTO HP 40 50 75 115
Transmission Hydrostatic only Any Any Any
Hydraulic GPM -- 5–20 5–20 5–20
Rotor Size 24" 24" 34" 34"
Number of Teeth 34 34 54 54
Tooth Part number S1000 S1000 S1000 S1000
Tooth Construction Carbide steel bolt-in Carbide steel bolt-in Carbide steel bolt-in Carbide steel bolt-in
Cutting Wheel Speed 540 RPM 810 RPM 810 RPM 1000 RPM
Cutting Height - Above Ground 10" 18" 25" 25"
Cutting Depth - Below Ground 6" 8" 14" 14"
Maximum Cutting Depth - Per Pass 5" 6" 9" 9"
Maximum Horizontal Cut 22" 22" 32" 32"
Swing Arc 65° 65° 65°
Hub Torque 803 Ft.-Lbs. 803 Ft.-Lbs. 803 Ft.-Lbs. 1050 Ft.-Lbs.
Over Torque Protection Slip clutch Slip clutch Slip clutch Slip clutch
Hitch Cat I Cat I or II Cat II Cat II
No. of Remotes Required - Hydraulic 0 1 or 2 1 or 2 1 or 2
Requires 12 Volt DC No No No No
Input Speed 540 540 540 1000
Unit Weight (Shipping) Lbs. 350 920 1231 1280
Width (Shipping) 48" 42" 48" 48"
Length (Shipping) 48" 49" 54" 54"
Model No. 1P24 3P24 3P34 3P40
Recommended HP Size 20-45 25-55 45-80 60-120
Maximum Engine HP 50 58 85 125
Maximum PTO HP 40 50 75 115
Transmission Hydrostatic only Any Any Any
Hydraulic GPM -- 5–20 5–20 5–20
Rotor Size 24" 24" 34" 34"
Number of Teeth 34 34 54 54
Tooth Part number S1000 S1000 S1000 S1000
Tooth Construction Carbide steel bolt-in Carbide steel bolt-in Carbide steel bolt-in Carbide steel bolt-in
Cutting Wheel Speed 540 RPM 810 RPM 810 RPM 1000 RPM
Cutting Height - Above Ground 10" 18" 25" 25"
Cutting Depth - Below Ground 6" 8" 14" 14"
Maximum Cutting Depth - Per Pass 5" 6" 9" 9"
Maximum Horizontal Cut 22" 22" 32" 32"
Swing Arc 65° 65° 65°
Hub Torque 803 Ft.-Lbs. 803 Ft.-Lbs. 803 Ft.-Lbs. 1050 Ft.-Lbs.
Over Torque Protection Slip clutch Slip clutch Slip clutch Slip clutch
Hitch Cat I Cat I or II Cat II Cat II
Quick hitch compatibility Yes No No No
No. of Remotes Required - Hydraulic 0 1 or 2 1 or 2 1 or 2
Requires 12 Volt DC No No No No
Input Speed 540 540 540 1000
Unit Weight (Shipping) Lbs. 350 920 1231 1280
Width (Shipping) 48" 42" 48" 48"
Length (Shipping) 48" 49" 54" 54"


Part #           Price
42in Root Base
1P 24
Price 20Hp 30Hp 40Hp 60Hp 70Hp 80Hp 90Hp 120Hp
-- 30 min 20 min 15 min -- -- -- -- --

1P24 only must but mounted on a hydrostatic drive tractor

3P 24
Price 20Hp 30Hp 40Hp 60Hp 70Hp 80Hp 90Hp 120Hp
-- -- 15 min 12 min 10 min -- -- -- --
3P 34
Price 20Hp 30Hp 40Hp 60Hp 70Hp 80Hp 90Hp 120Hp
-- -- -- -- 6 min 5 min 4 min -- --
3P 40
Price 20Hp 30Hp 40Hp 60Hp 70Hp 80Hp 90Hp 120Hp
-- -- -- -- 6 min 5 min 4 min 3 min 2 min
Service Videos
Parts breakdown
Owner
Warranty form
Local dealer support
logo
logo
Updated as of February 23, 2024 4:59 PM EST

UPCOMING PUBLIC HOLIDAYS

Date Description

STUMP GRINDERS

Model Number Discount Available Lead time to build
first order
Lead time to build
next order
Location Notes Discount Description
WB4410% MTBOver stock on some parts
HGW30 MTB
1P24
D005735 Extension bracket kit for 1P24
S1050 S1050 valve kit (shipped w/o stump grinder)
3P2412% MTBRefurbished at factory with new gearbox and rotor
3P24-S1050 S1050 kit mounted.
3P34
3P34-S1050 S1050 kit mounted.
3P40
3P40-S1050 S1050 kit mounted.
S14-S25015% MTBStock w/D001126 mini plateFactory refurbished, full warranty
S14-S450
S16-S508
S18-S450 MTBStock w/D001127 plate
S18-S550 MTBStock w/D001127 plate
S18-S650 MTBStock w/D001127 plate
S24-S445
S24-S545
S28-S645
S40-S740
S40-S770
HGS50F
GXM350-X508
GXM350-X510
GXM350-X530
GXM550-X508
GXM550-X510
GXM550-X530
GXM550-X540
GXM550-X550
GXM550-X590
GXM750-X54010% 5% discount on stock floor modelNew floor model with full warranty
GXM750-X550
GXM750-X570
GXM750-X590

PUBLIC HOLIDAYS

Date Description
2024-03-29Good Friday
2024-05-20Victoria Day