CF360 CF372 CF560 CF572 CSC744 CSC760

CF360 Skid Steer Rotary Brush Cutter Model

The rugged frame of the CF360 heavy-duty rotary brush mower houses two AR400 blades featuring a 70" path width. The 1/4” steel deck is designed to stand up and perform in rough terrain while cutting small trees, brush, unwanted weeds and grass. The 60" mouth of this unit is protected by a heavy-duty chain that controls flying debris, but still allows brush to easily enter. The rear of the unit is also guarded by a chain curtain so standing brush enters and mulched debris exits as you break new trails, clear ditches, construction, property sites, and other overgrown areas.
Chain curtains are standard front and rear, on the 300 series.

Two Cuts per Pass

As the rotating rotor mass throws the slasher blades at small diameter trees, the blade slices small sections away as the Brush Cutt advances forward. The curved cutting tips of the slasher blades give the Brush Cutt two cuts per pass of each blade. The leading tip takes a small bite and is immediately followed by the second tip taking another bite at 26–52 slashes per second with devastating results. Available in either 2 or 4 blade configurations the Brush Cutt’s reversible/replaceable blades are made of long lasting 1/4" AR 400 steel.

Two Cuts per Pass and a Real Slasher

Gear Box

Standard on all Brush Cutt models is a relief valve. Set at 3,000 psi, this valve disengages the driveline if the hydraulic system pressure is too great, thereby protecting both the skidsteer and the Brush Cutt.

The Brush Cutt uses a bevel gearbox capable of handling up to 90HP for final drive output. More durable than conventional direct drive setups, these gearboxes prevent shocks from cutting being passed to the drive motor.

Gear Box

Hose Armour

Standard on all Brush Cutt models is Hose Armour. This is a tough wrap which coils around the hoses and protects them from the harsh environment of brush cutting. The armour helps to prevent any punctures from fallen brush or trees.

Hose Armour

Slasher Blades

Crafted from 1/4" AR 400 steel, the unique profile of the slasher blades provides increased cutting surface. The blade’s thin reversible profile continuously provides a sharp edge.

Slasher Blades

Blade Mount

To secure slasher blades to the blade assembly, Baumalight uses Gr. 8 bolts capped off with castle nuts and cotter pins. The blade mount uses a fully welded collar to drop the blade; this spacing helps to reduce the blade from binding while in operation.

Blade Mount

2-Way Model

2-Way models feature a durable one piece rotor assembly. Constructed of a single 3/4" plate of steel and finished with a slasher blade on each end. The 2-way blade models provide up to 26 slashes per second.

2-Way Model

Front & Rear Chain Curtains

A heavy-duty chain curtain reduces discharge of debris. Unlike traditional chain curtains, Baumalight’s Brush Cutt uses a curtain rod setup that is free of welds. This setup allows the chain to absorb the impacts and places less strain on the welded link for longer curtain life.

Chain Curtain

Shield

To protect the output shaft from impact or contamination caused by debris, each model of Brush Cutt is finished off with a heavy-duty output shaft shield.

Shield

Powder Coated Finish

Heavy-duty construction and a durable powder-coated finish.

Powder Coated Finish

Anti-Slip Strip

Extra traction from anti-slip strips provides improved safety as well as ease of entry and exit from the cab.

Anti-Slip Strip

Two Cuts per Pass

As the rotating rotor mass throws the slasher blades at small diameter trees, the blade slices small sections away as the Brush Cutt advances forward. The curved cutting tips of the slasher blades give the Brush Cutt two cuts per pass of each blade. The leading tip takes a small bite and is immediately followed by the second tip taking another bite at 26–52 slashes per second with devastating results. Available in either 2 or 4 blade configurations the Brush Cutt’s reversible/replaceable blades are made of long lasting 1/4" AR 400 steel.

Two Cuts per Pass and a Real Slasher

Gear Box

Standard on all Brush Cutt models is a relief valve. Set at 3,000 psi, this valve disengages the driveline if the hydraulic system pressure is too great, thereby protecting both the skidsteer and the Brush Cutt.

The Brush Cutt uses a bevel gearbox capable of handling up to 90HP for final drive output. More durable than conventional direct drive setups, these gearboxes prevent shocks from cutting being passed to the drive motor.

Gear Box

Hose Armour

Standard on all Brush Cutt models is Hose Armour. This is a tough wrap which coils around the hoses and protects them from the harsh environment of brush cutting. The armour helps to prevent any punctures from fallen brush or trees.

Hose Armour

Slasher Blades

Crafted from 1/4" AR 400 steel, the unique profile of the slasher blades provides increased cutting surface. The blade’s thin reversible profile continuously provides a sharp edge.

Slasher Blades

Blade Mount

To secure slasher blades to the blade assembly, Baumalight uses Gr. 8 bolts capped off with castle nuts and cotter pins. The blade mount uses a fully welded collar to drop the blade; this spacing helps to reduce the blade from binding while in operation.

Blade Mount

2-Way Model

2-Way models feature a durable one piece rotor assembly. Constructed of a single 3/4" plate of steel and finished with a slasher blade on each end. The 2-way blade models provide up to 26 slashes per second.

2-Way Model

Front & Rear Chain Curtains

A heavy-duty chain curtain reduces discharge of debris. Unlike traditional chain curtains, Baumalight’s Brush Cutt uses a curtain rod setup that is free of welds. This setup allows the chain to absorb the impacts and places less strain on the welded link for longer curtain life.

Chain Curtain

Shield

To protect the output shaft from impact or contamination caused by debris, each model of Brush Cutt is finished off with a heavy-duty output shaft shield.

Shield

Powder Coated Finish

Heavy-duty construction and a durable powder-coated finish.

Powder Coated Finish

Anti-Slip Strip

Extra traction from anti-slip strips provides improved safety as well as ease of entry and exit from the cab.

Anti-Slip Strip
Model No. CF360 CF372 CF560 CF572 CSC744 CSC760
Available Motor Options M450, M550, M650 M450, M550, M650 M450, M550, M650 M450, M550, M650 HS430,HS450,HS490 C790
Recommended GPM Check Motor Options Check Motor Options Check Motor Options Check Motor Options Check Motor Options Check Motor Options
Maximum Brush Size 2" 2" 4" 4" 10"
Discharge Protection Link Chain Curtain
Front and Back
Link Chain Curtain
Front and Back
Open Front with Push Bar Link Chain Curtain on Back Open Front with Push Bar Link Chain Curtain on Back Double chain on back Double chain on back
Path Width 70" 82" 70" 82" 57" 72"
Cutting Width 60" 72" 60" 72" 44" 60"
Low Cutting Height 2.5" 2.5" 2.5" 2.5" 1/2" 1/2"
Number of Blades 2 2 4 4 20 pcs R7000 30 pcs R7000
Attachment Type Universal Skid-Steer Plate Universal Skid-Steer Plate Universal Skid-Steer Plate Universal Skid-Steer Plate Universal Skid-Steer Plate Universal Skid-Steer Plate
Maximum HP Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer
Min Carrier Weight 4,000 lb 4,500 lb 4,500 lb 5,000 lb 5,500 lb 7,000 lb
System Protection Built In Hydraulic Built In Hydraulic Built In Hydraulic Built In Hydraulic Built In Hydraulic Built In Hydraulic
Dimensions (LxWxH) 88"x72"x36" 90"x84"x36" 88"x72"x36" 90"x84"x36" 88"x75"x67"
Deck Structure 1/4" steel 1/4" steel 1/4" steel 1/4" steel 1/4" T1 Steel 1/4" T1 Steel
Unit Weight 1342 lbs. 1390 lbs. 1540 lbs. 1570 lbs. 2000 lbs. 2850 lbs.
Model No. CF360 CF372 CF560 CF572 CSC744 CSC760
Available Motor Options M450, M550, M650 M450, M550, M650 M450, M550, M650 M450, M550, M650 HS430,HS450,HS490 C790
Recommended GPM Check Motor Options Check Motor Options Check Motor Options Check Motor Options Check Motor Options Check Motor Options
Maximum Brush Size 2" 2" 4" 4" 10"
Discharge Protection Link Chain Curtain
Front and Back
Link Chain Curtain
Front and Back
Open Front with Push Bar Link Chain Curtain on Back Open Front with Push Bar Link Chain Curtain on Back Double chain on back Double chain on back
Path Width 70" 82" 70" 82" 57" 72"
Cutting Width 60" 72" 60" 72" 44" 60"
Low Cutting Height 2.5" 2.5" 2.5" 2.5" 1/2" 1/2"
Number of Blades 2 2 4 4 20 pcs R7000 30 pcs R7000
Attachment Type Universal Skid-Steer Plate Universal Skid-Steer Plate Universal Skid-Steer Plate Universal Skid-Steer Plate Universal Skid-Steer Plate Universal Skid-Steer Plate
Maximum HP Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer Check Flow & PSI on Skid Steer
Min Carrier Weight 4,000 lb 4,500 lb 4,500 lb 5,000 lb 5,500 lb 7,000 lb
System Protection Built In Hydraulic Built In Hydraulic Built In Hydraulic Built In Hydraulic Built In Hydraulic Built In Hydraulic
Dimensions (LxWxH) 88"x72"x36" 90"x84"x36" 88"x72"x36" 90"x84"x36" 88"x75"x67"
Deck Structure 1/4" steel 1/4" steel 1/4" steel 1/4" steel 1/4" T1 Steel 1/4" T1 Steel
Unit Weight 1342 lbs. 1390 lbs. 1540 lbs. 1570 lbs. 2000 lbs. 2850 lbs.
Brush Cutt Illustration
how to read

M450 Motor

M550 Motor

650 Motor

HOW TO CHOOSE THE RIGHT MOTOR

The most important part of choosing the right BrushFire is matching the correct motor option to your equipment. It can make a huge difference. In this video, we explain how to use our charts to determine which motor is right for you!

Understanding Motor Understanding Motor
Hydraulic Flow & Pressure Hydraulic Flow & Pressure
logo
logo
Updated as of December 13, 2018 5:19 PM EST

UPCOMING PUBLIC HOLIDAYS

Date Description

BRUSH CUTTERS

Model Number Discount Available Number of Business Days
to build first order
Number of Business Days
to build next order
Location Notes Discount Description
CF360611
CF56015%211MIDiscounted Unit in MIFloor Model - Old Stock
CF3725% to 25% (requires email consultation with Menno)211Media Discount
CF572-M450Stock6BPM450
CF572-M550Stock6BPM550
CF572-M65066BPM650
CP560Stock11
CP5725% to 25% (requires email consultation with Menno)1010Media Discount
CX3601616
CX3726161New Model
CXC5305% to 25% (requires email consultation with Menno)611Media Discount
CXC5425% to 25% (requires email consultation with Menno)611Media Discount
CXC550214
CSC7445%712Demo Unit with HS430 Motor
CSC7605% to 25% (requires email consultation with Menno)Stock14MTBMedia Discount
All Brush Cutt5% to 25% (requires email consultation with Menno)Stock7looking for more video on all modelsMedia Discount

PUBLIC HOLIDAYS

Date Description
2018-12-21Closing at noon for Christmas week, reopening on Jan 2 2019
2018-12-24Closed for Christmas Week, reopening on Jan 2 2019
2018-12-31Closed for Christmas Week, reopening on Jan 2 2019