PUT SOME
TEETH
INTO IT
PUT SOME
TEETH
INTO IT
The 900 series Baumalight mulchers will efficiently mulch heavy brush and trees and are designed for contractors, rental and any other heavy duty mulching and land clearing. The MP972 masticating head Brush Mulcher is designed to fit tractors with 90 - 135 HP and Cat 2 or 3 3PH. The 900 Series teeth are available in either Ripper or Planer style. The carbide Ripper tooth is the good general use tooth. Their v-shaped design shreds through brush and makes them less vulnerable in areas plagued by rocks and debris. The 900 Series Planer style tooth provides the most efficient cutting by smoothly chipping away at the brush. Its flat profile however makes it vulnerable to shattering on impact with rocks and other debris. Tractor mounted brush mulchers are not limited to reverse only, drive forward over your mulch and turn it into a finer mulch. A usefull feature on the Baumalight MP972 Brush Mulcher is the opening cutting shield. This allows you to adjust for a better, higher angle of attack on bigger brush or keep it closed and control the mulch for even finer results. With direct drive from the engine, all the way through the heavy duty gear box, to the teeth, the MP972 PTO Brush Mulcher is a very efficient way to clear heavy brush and small trees.
All Baumalight products are sold through our network of equipment dealers. For you, this means better product support, after-sales service, maintenance and product warranty from your local, trusted dealership Click here to find a local dealer.
Baumalight offers customers a series of helpful service & instructional videos and supports the right to repair. These videos show you how to perform your own trouble shooting and repairs which can save you a lot of down time because many things can be fixed on the spot by end users. Also, after the warranty period is over, a lot of money can be saved if you can do things yourself following simple instructions on trouble shooting, maintenance and repairs.
CLICK THE VIDEO TO LEARN MORE
The integrated brush bar helps control the brush and bend taller brush for easier mulching.
These two position skid shoes allow you to adjust the cutting height for optimal clearing performance.
The force and impact of mulching often bends the teeth. Our V-Notch teeth and hardened holders hold the tooth firmly in place to absorb impacts from multiple directions.
These heavy-duty tooth holders resist bending and keep you working longer.
All MP572 Brush Mulchers come with a free set of 6 replacement teeth. These replacement teeth are conveniently shipped in a robust enclosed compartment on top of the frame.
The 500 Series teeth come in two carbide tipped styles; Planer and Ripper. The Planer style teeth take small bites and provide the most efficient mulching and cutting. The Ripper style teeth have more of a shredding mulching action. Their v-shaped design makes them less susceptible to impacts with hard objects like stones, making them the better choice when mulching below grade and in fence lines. Both styles are Bolt-on replaceable for quick and easy servicing and replacement even in the field.
All units shipped with Standard P5000 Series Planer Teeth only and ripper teeth can be installed as the planer teeth need replacing. Units can be operated with a mix of Planer and Ripper teeth.
For smoother mulching, the spiral tool pattern allows one tooth to engage at a time.
To protect the gearbox and drive sytem, Baumalight PTO mulchers come with a slip clutch. Automatically disengaging the clutch at a predetermined torque.
Heavy duty gearbox for high performance and better mulching power and long life.
The single debris door is controlled hydraulically from the cab to give the operator more control of the mulching action. When closed the mulch debris is more controlled and a finer mulch is produced
A heavy duty reinforced belt delivers the force from the gear box to the rotor. This offers protection from the shocks inherent in mulching.
Protective steel cover that prevents damage from wire fencing.
The rear of the unit is guarded by a chain curtain so standing brush enters and mulched debris exits.
Baumalight mulchers feature grease pins on all pivot points, reducing the risk of equipment damage and providing long life and easy servicing.
Spring Bushings made from high grade chrome-vanadium AISI 6150 spring steel on all main pivot points.
Heavy duty frame with T1 alloy tool steel sheet metal for all the main areas. Powder coated frame with multiple anti-slip pads to give you secure footing for ease of entry and exit from your cab.
Our powder coat finish is much tougher than conventional paint to stand up to the rigors of mulching and helps prevent rusting.
All hoses are sleeved for operator and hose protection. The Connecting hoses are sleeved and wrapped in hose armour for double protection.
All Baumalight products are sold through our network of equipment dealers. For you, this means better product support, after-sales service, maintenance and product warranty from your local, trusted dealership Click here to find a local dealer.
Baumalight offers customers a series of helpful service & instructional videos and supports the right to repair. These videos show you how to perform your own trouble shooting and repairs which can save you a lot of down time because many things can be fixed on the spot by end users. Also, after the warranty period is over, a lot of money can be saved if you can do things yourself following simple instructions on trouble shooting, maintenance and repairs.
CLICK THE VIDEO TO LEARN MORE
Save time by easily replacing the AR400 steel wear plates on the ms960 without needing to remove the rotor.
If you are mulching and you catch some old fence wire, it can really cause damage to the unit if the wire slips over the edge of the rotor and gets wrapped around the shaft. The wire can get bunched against the bearings, causing major damage. Our wire protection kit contains a welded raised area on the end of the rotor that protects the shaft and prevents wire from getting in.
The rear of the unit is guarded by a 3/8" thick chain curtain so standing brush enters and mulched debris exits.
Reduce your regular maintenance time by easily greasing the bearings on the MP972 from outside the frame. No tools required.
To protect the gearbox and drive system, Baumalight PTO mulchers come with a slip clutch. Automatically disengaging the clutch at a predetermined torque.
Heavy duty gearbox for high performance and better mulching power and long life.
A heavy duty reinforced belt delivers the force from the gear box to the rotor. This offers protection from the shocks inherent in mulching.
Baumalight mulchers feature grease pins on all pivot points, reducing the risk of equipment damage and providing long life and easy servicing.
Spring Bushing made from high grade chrome-vanadium AISI 6150 spring steel on all main pivot points.
The adjustable belt tensioner ensures the proper tension of your belts, with no extra idler wheel that could wear out. Simply loosen the bolts and raise the motor mount to tighten the belt.
Built into the pusher bar, the directional felling hook will directionally control wayward trees, sprawling clumps and low hanging limbs.
All hoses are sleeved for operator and hose protection. The Connecting hoses are sleeved and wrapped in hose armour for double protection.
Now completely redesigned for the 900 series Brush Mulcher, the heavy duty steel frame is constructed with T1 alloy tool steel sheet metal.
The MP972 is the only Baumalight mulcher with an adjustable back door, this can be raised for forward driving with ground engagement and lowered for backward driving into the brush.
Equipped with front and rear hydraulically controlled debris doors. They are controlled from the cab to give the operator more control of the mulching action. When front door is closed, the mulch debris is more controlled and a finer mulch is produced. Open the rear door to better attack stubborn brush by exposing more of the rotor.
When push comes to shove, the integrated push bar helps control
Our powder coat finish is much tougher than conventional paint to stand up to the rigors of mulching and helps prevent rusting.
All MP972 Brush Mulchers come with a free set of 6 replacement teeth. These replacement teeth can be convenienty stored in the enclosed spare tool compartment.
There are currently no customer photos or video submitted for this Baumalight product.Please check out similar products to see if there are submitted media available for those . Visit our Factory Discount web page to learn how you could participate in our Media Discount Program with your Baumalight product.
| Model No. | MP348 | MP360 | MP560 | MP572 | MP972 | Large Shaft to up the HP |
|---|---|---|---|---|---|---|
| Path Width | 60" | 72" | 75" | 87" | 84" | D002134 |
| Rotor Width | 48" | 60" | 60" | 72" | 72" | |
| Maximum Engine HP | 50 | 55 | 75 | 125 | 135 | 90 - 155 PTO Hp |
| Maximum PTO HP | 40 | 45 | 65 | 115 | 125 | Do not exceed 165 Engine Hp |
| Minimum Engine HP | 25 | 30 | 45 | 50 | 90 | |
| Cutting Depth | Level | Level | 1.5" Above to 1" Below Grade | 1.5" Above to 1" Below Grade | Level to 2" Below Grade | |
| Cutting Style | High Speed Teeth | High Speed Teeth | Carbide Tipped Bolt In | Carbide Tipped Bolt In | Double Tipped | |
| Tooth Part number | H3000 | H3000 | P5000 | P5000 | R9000 | |
| Number of Cutters | - | - | 126 | 160 | - | |
| Number of cutters (if shipped with new spiral tooth pattern) | 60 | 74 | 92 | 112 | 43 | |
| Rotor Shaft Size | 2" | 2" | 2" | 2" | 2" | |
| Rotor Diameter (tool tips) | 15" | 15" | 15" | 15" | 18.5" | |
| Rotor Weight (with tools) | 230 lbs | 315 lbs | 575 lbs | 700 lbs | 1,105 lbs | |
| Hitch Size | CAT 1 | CAT 1 | CAT 2 | CAT 2 | CAT 2 or 3 | |
| Quick hitch compatibility | Yes | Yes | No | No | No | No |
| Drive Speed | 540 | 540 | 540 | 1,000 | 1,000 | |
| Drive Speed Options | 540 (Max Engine HP 110) | 540 (Max Engine HP 110) | ||||
| Gearbox Spline Size | 1-3/8" | 1-3/8" | 1-3/8" | 1-3/8" | 1-3/8" | |
| Tractor End Spline Size | 1-3/8" | 1-3/8" | 1-3/8" | 1-3/8" | 1-3/8" | 1.75" 20 -spline |
| System Protection | Slip Clutch | Slip Clutch | Slip Clutch | Slip Clutch | Slip Clutch | |
| Unit Weight | 1050 lbs | 1200 lbs | 2145 lbs | 2500 lbs | 3200 lbs | |
| Hydraulic Requirements | Not Applicable | Not Applicable | 1 Remote | 1 Remote | 2 Remotes |
| Model No. | MP348 | MP360 | MP560 | MP572 | MP972 | Large Shaft to up the HP |
|---|---|---|---|---|---|---|
| Path Width | 60" | 72" | 75" | 87" | 84" | D002134 |
| Rotor Width | 48" | 60" | 60" | 72" | 72" | |
| Maximum Engine HP | 50 | 55 | 75 | 125 | 135 | 90 - 155 PTO Hp |
| Maximum PTO HP | 40 | 45 | 65 | 115 | 125 | Do not exceed 165 Engine Hp |
| Minimum Engine HP | 25 | 30 | 45 | 50 | 90 | |
| Cutting Depth | Level | Level | 1.5" Above to 1" Below Grade | 1.5" Above to 1" Below Grade | Level to 2" Below Grade | |
| Cutting Style | High Speed Teeth | High Speed Teeth | Carbide Tipped Bolt In | Carbide Tipped Bolt In | Double Tipped | |
| Tooth Part number | H3000 | H3000 | P5000 | P5000 | R9000 | |
| Number of Cutters | - | - | 126 | 160 | - | |
| Number of cutters (if shipped with new spiral tooth pattern) | 60 | 74 | 92 | 112 | 43 | |
| Rotor Shaft Size | 2" | 2" | 2" | 2" | 2" | |
| Rotor Diameter (tool tips) | 15" | 15" | 15" | 15" | 18.5" | |
| Rotor Weight (with tools) | 230 lbs | 315 lbs | 575 lbs | 700 lbs | 1,105 lbs | |
| Hitch Size | CAT 1 | CAT 1 | CAT 2 | CAT 2 | CAT 2 or 3 | |
| Quick hitch compatibility | Yes | Yes | No | No | No | No |
| Drive Speed | 540 | 540 | 540 | 1,000 | 1,000 | |
| Drive Speed Options | 540 (Max Engine HP 110) | 540 (Max Engine HP 110) | ||||
| Gearbox Spline Size | 1-3/8" | 1-3/8" | 1-3/8" | 1-3/8" | 1-3/8" | |
| Tractor End Spline Size | 1-3/8" | 1-3/8" | 1-3/8" | 1-3/8" | 1-3/8" | 1.75" 20 -spline |
| System Protection | Slip Clutch | Slip Clutch | Slip Clutch | Slip Clutch | Slip Clutch | |
| Unit Weight | 1050 lbs | 1200 lbs | 2145 lbs | 2500 lbs | 3200 lbs | |
| Hydraulic Requirements | Not Applicable | Not Applicable | 1 Remote | 1 Remote | 2 Remotes |
| MODEL | TRACTOR SPEED | RPM | 100 HP | 125 HP | 150 HP |
|---|---|---|---|---|---|
| MP972 | Low Gear Creeper Hydrostatic |
1800 | 7" 9" 13" |
9" 10" 15" |
10" 12" 17" |
| Date | Description |
|---|
| Model Number | Discount Available | Lead time to build first order | Lead time to build next order | Location | Notes | Discount Description |
|---|---|---|---|---|---|---|
| MP348-540 | ||||||
| MP360-540 | ||||||
| MP560-540 | ||||||
| MP572-540 | ||||||
| MP572-1000 | ||||||
| MP972-540 | ||||||
| MP972-1000 | ||||||
| MS348-A450 | ||||||
| MS548 | ||||||
| MS548-C510 | ||||||
| MS548-C530 | ||||||
| MS560 | ||||||
| MS560-C510 | ||||||
| MS560-C530 | ||||||
| MS560-C540 | ||||||
| MS560-C550 | ||||||
| MS572 | ||||||
| MS572-C530 | ||||||
| MS572-C540 | ||||||
| MS572-C550 | ||||||
| MS960 | ||||||
| MS960-C940 | ||||||
| MS960-C950 | ||||||
| MS960-D97X2 | 2 speed motor | |||||
| MS972 | ||||||
| MS972-C940 | ||||||
| MS972-C950 | ||||||
| MS972-D97X2 | 2 speed motor | |||||
| MS1160 | ||||||
| MS1160-C1150 | ||||||
| MS1160-D117X2 | 2 speed motor | |||||
| MX230-F2000 | 15-30% on purchase plus cash back | Extra discount for supplying action shot videos - End user must fill out https://baumalight.com/factorydiscounts/contact_us/ form to get started | ||||
| MX230-F3000 | 15-30% on purchase plus cash back | Extra discount for supplying action shot videos - End user must fill out https://baumalight.com/factorydiscounts/contact_us/ form to get started | ||||
| MX330-A450 | ||||||
| MX530 | ||||||
| MX530-C508 | Stock unit w/o mount | |||||
| MX530-C510 | Stock unit w/o mount | |||||
| MX530-C530 | Stock unit w/o mount | |||||
| MX530R | ||||||
| MX530R-C510 | ||||||
| MX530R-C530 | Stock unit w/o mount | |||||
| MX548R | ||||||
| MX948R | ||||||
| MX960R | ||||||
| MX1160R |
| Date | Description |
|---|---|
| 2023-10-09 | Canadian Thanks Giving |
