The rugged frame of this excavator bush mower, featuring a 70" path width, is designed to stand up and perform in rough terrain. The hungry 60" mouth of this unit is protected by a heavy-duty chain that controls flying debris, but still allows brush to easily enter. The rear of the unit is also guarded by a chain curtain so standing brush enters and mulched debris exits.
As the rotating rotor mass throws the slasher blades at small diameter trees, the blade slices small sections away as the Brush Cutt advances forward. The curved cutting tips of the slasher blades give the Brush Cutt two cuts per pass of each blade. The leading tip takes a small bite and is immediately followed by the second tip taking another bite at 26–52 slashes per second with devastating results. Available in either 2 or 4 blade configurations the Brush Cutt’s reversible/replaceable blades are made of long lasting 1/4" AR 400 steel.
Standard on all Brush Cutt models is a relief valve. Set at 3,000 psi, this valve disengages the driveline if the hydraulic system pressure is too great, thereby protecting both the skidsteer and the Brush Cutt.
The Brush Cutt uses a bevel gearbox capable of handling up to 90HP for final drive output. More durable than conventional direct drive setups these gearboxes prevent shocks from cutting being passed to the drive motor.
Crafted from 1/4" AR 400 steel, the unique profile of the slasher blades provides increased cutting surface. The blades thin reversible profile continuously provides a sharp edge.
To secure slasher blades to the blade assembly, Baumalight uses Gr. 8 bolts capped off with castle nuts and cotter pins. The blade mount uses a fully welded collar to drop the blade—this spacing helps to reduce the blade from binding while in operation.
Designed for easy service, the 3-Way models feature a heavy-duty rotor with 3 fixed extensions. Each extension is finished off with a slasher blade. This configuration is capable of providing up to 39 slashes per second.
Using a 3/4" top plate and a 3/8" bottom plate this heavy-duty rotor sandwiches the three–way blade assembly in place.
To protect the output shaft from impact or contamination caused by debris, each model of Brush Cutt is finished off with a heavy duty output shaft shield.
All Excavator Brush Cutt models are available with Baumalight’s Pack Wing PTO power packs for more carrier versatility. Click for more…
As the rotating rotor mass throws the slasher blades at small diameter trees, the blade slices small sections away as the Brush Cutt advances forward. The curved cutting tips of the slasher blades give the Brush Cutt two cuts per pass of each blade. The leading tip takes a small bite and is immediately followed by the second tip taking another bite at 26–52 slashes per second with devastating results. Available in either 2 or 4 blade configurations the Brush Cutt’s reversible/replaceable blades are made of long lasting 1/4" AR 400 steel.
Standard on all Brush Cutt models is a relief valve. Set at 3,000 psi, this valve disengages the driveline if the hydraulic system pressure is too great, thereby protecting both the skidsteer and the Brush Cutt.
The Brush Cutt uses a bevel gearbox capable of handling up to 90HP for final drive output. More durable than conventional direct drive setups these gearboxes prevent shocks from cutting being passed to the drive motor.
Crafted from 1/4" AR 400 steel, the unique profile of the slasher blades provides increased cutting surface. The blades thin reversible profile continuously provides a sharp edge.
To secure slasher blades to the blade assembly, Baumalight uses Gr. 8 bolts capped off with castle nuts and cotter pins. The blade mount uses a fully welded collar to drop the blade—this spacing helps to reduce the blade from binding while in operation.
Designed for easy service, the 3-Way models feature a heavy-duty rotor with 3 fixed extensions. Each extension is finished off with a slasher blade. This configuration is capable of providing up to 39 slashes per second.
Using a 3/4" top plate and a 3/8" bottom plate this heavy-duty rotor sandwiches the three–way blade assembly in place.
To protect the output shaft from impact or contamination caused by debris, each model of Brush Cutt is finished off with a heavy duty output shaft shield.
All Excavator Brush Cutt models are available with Baumalight’s Pack Wing PTO power packs for more carrier versatility. Click for more…
| Model No. | CXC530 | CXC542 | CXC550 |
|---|---|---|---|
| Excavator Adaptor Code | A02 | A02 | A03 |
| Available Motor Options | HX508, HX510, HX530 | HX530, HX550, HX570 | HX550, HX570, HX590 |
| Recommended GPM | Check Motor Options Chart | ||
| Maximum Brush Size | 3.5" | 5" | 6" |
| Discharge Protection | Open Front and Back | ||
| Path Width | 40" | 50" | 67" |
| Cutting Width | 30" | 42" | 50" |
| Low Cutting Height | 2.5" | 2.5" | 2.5" |
| Number of Blades | 3 | 3 | 3 |
| Slashes per Second | 80 | 80 | 90 |
| Attachment Type | Bolt-On | ||
| Maximum HP | Check Flow & PSI on Carrier | ||
| Min Carrier Weight | 2 ton | 3 ton | 8 ton |
| Max Carrier Weight | 10 ton | 15 ton | 20 ton |
| System Protection | Hydraulic Relief Value | ||
| Deck Structure | 1/4" AR400 steel | 1/4" AR400 steel | 3/8" AR400 steel |
| Unit Weight | 550 lbs | 640 lbs | 1,380 lbs |
| Model No. | CXC530 | CXC542 | CXC550 |
|---|---|---|---|
| Baumalight Connection Code | A02 | A02 | A03 |
| Available Motor Options | HX508, HX510, HX530 | HX530, HX550, HX570 | HX550, HX570, HX590 |
| Recommended GPM | Check Motor Options Chart | ||
| Maximum Brush Size | 3.5" | 5" | 6" |
| Discharge Protection | Open Front and Back | ||
| Path Width | 40" | 50" | 67" |
| Cutting Width | 30" | 42" | 50" |
| Low Cutting Height | 2.5" | 2.5" | 2.5" |
| Number of Blades | 3 | 3 | 3 |
| Slashes per Second | 80 | 80 | 90 |
| Attachment Type | Bolt-On | ||
| Maximum HP | Check Flow & PSI on Carrier | ||
| Case Drain | Critical | Critical | Critical |
| Min Carrier Weight | 2 ton | 3 ton | 8 ton |
| Max Carrier Weight | 10 ton | 15 ton | 20 ton |
| Deck Structure | 1/4" AR400 steel | 1/4" AR400 steel | 3/8" AR400 steel |
| Unit Weight | 550 lbs | 640 lbs | 1,380 lbs |
HOW TO CHOOSE THE RIGHT MOTOR
The most important part of choosing the right Brush Mulcher is matching the correct motor option to your equipment. It can make a huge difference. In this video, we explain how to use our charts to determine which motor is right for you!
| Date | Description |
|---|
| Date | Description |
|---|---|
| 2024-05-20 | Victoria Day |
